หมวดสินค้า

หมวดสินค้า

AWL003 : เครื่องควบคุมระดับน้ำอัตโนมัติ ลูกลอยอัตโนมัติ DF96 ED AC 220V 10A Din Rail Mount Float Switch Auto Water Level Controller with 3 probes สายเซนเซอร์ 2m

790 บาท
มีสินค้าอยู่ 1
เครื่องควบคุมระดับน้ำอัตโนมัติ ลูกลอยอัตโนมัติ DF96 ED AC 220V 10A Din Rail Mount Float Switch Auto Water Level Controller with 3 probes สายเซนเซอร์ 2m

>> เช็คสต๊อคสินค้า <<

รายละเอียดสินค้า
  • รุ่นสินค้า: DF-96ED 
  • แรงดันไฟฟ้า: AC 220V/50HZ
  • กระแสสูงสุด: 10A (ใช้การหน่วงเวลา 30A)
  • การติดตั้ง: ติดตั้งบนราง
  • การใช้พลังงาน: ≤2W
  • การส่งผ่านสัญญาณ : รัศมี 500 เมตร
  • ขนาด: 126 * 88 * 51 มม.
แพคเกจ: 
  • สวิตช์ควบคุมระดับน้ำ 1 ชิ้น
  • เซนเซอร์ 200 ซม. 3 ชิ้น

Single-control UP pool (water storage) installation instructions shown in figure 1

  • A(red)-Upper water level control point. When water level gets to A point, the probe touch water and controller can stop the pump by auto.
  • B(blue)-Lower water level control point. When water level gets off B point, the probe out of reach water and controller can start the pump by auto.
  • C(black)-Should be placed in bottom of pool as the common line.
  • D(green) and E(yellow)are connected with C (black).

Single-control DOWN pool(drain water)installation instructions shown in figure 2.

  • E-Upper water level control point. When water level gets to E point, the probe touch water and controller can start the pump by auto.
  • D-Lower water level control point. As liquid level gets off D point, the probe out of reach water and controller can stop the pump by auto.
  • C-Should be placed in bottom of pool as the common line.
  • A&B-disconnected
  Lack of water protection installation instructions shown in figure 3.
  • C&D-Lower water level control points. When water level gets off this point,
  • C or D probe out of reach water and controller can stop the pump by auto.
  • E&C-short-connected;
  • A&B-disconnected
  Joint control UP and DOWN pool installation instructions shown in figure 4.
  • A-Upper water level control point in UP pool. When water level gets to A point,the probe touch water and controller can stop the pump by auto.
  • B-Lower water level control point in UP pool. When water level gets off A point, the probe out of reach water and controller can start the pump by auto.
  • C-Should be placed in bottom of UP and DOWN pools as the common line.
  • D-Lower water level control point in DOWN pool. When water level gets off D point, the probe out of reach and controller can stop the pump by auto.
  • E-Upper water level control point in DOWN pool. When water level gets to E point, the probe reach water and controller can start the pump by auto. Then pool starts to drain water. If not, E point disconnected
Used to solve problem: 1. On power but no work:
  • a. Check the red indicator is on or not. If not, make the connection is good enough;
2. When water level is above or below probes but the pump does not start or stop by auto, Please check it like the following.
  • a. Whether the probe is placed too high or low so that water level can reach or out of reach it
  • b. The connection of upper &lower line or probe is dislocation by error or short connected
  • c. To check the probe whether it is rust or not or the connection is good enough.
  • d. C- Check the common line whether it is placed in the lowermost bottom of pool.
    Product Description
  • Type: DF-96ED Updated version
  • Working voltage: AC 220V/50HZ
  • Max Current: 10A(Use the 30A Delay)
  • Installation: Din Rail Mount
  • Power consumption≤2W
  • transmission signal: 500M
  • Size: 126*88*51mm
Package include:
  • 1pcs Automatic Water Level Controller Switch
  • 3pcs 200CM Sensor
  รับประกันสินค้า 3 เดือน

ข้อมูลจำเพาะ

Information on technical characteristics, the delivery set, the country of manufacture and the appearance of the goods is for reference only and is based on the latest information available at the time of publication.
Menu